R&D Plumbing Co. LLC

November 18, 2026

BY R&D PLUMBING CO. LLC

Commercial Kitchen Grease Trap Requirements for Fairhope Restaurants

I break down what Fairhope restaurants need to know about grease traps and interceptors, how they're sized and plumbed, and who to call before you build.

If you're opening or renovating a restaurant in Fairhope, grease handling is one of the first things you need to sort out, not the last. The grease trap or interceptor has to be sized for your kitchen, plumbed correctly, and approved before you're serving food. Get it wrong and you're looking at backups, failed inspections, and work you've already paid for being torn back out.

Here's what I walk restaurant owners through before we ever put a pipe in the ground.

What does a grease trap actually do?

Every commercial kitchen puts fats, oils, and grease down the drain. Dishwashers, prep sinks, wok stations, fryers. That stuff doesn't just flow away. It cools, hardens, and sticks to the inside of your lines until it chokes them off.

A grease trap or interceptor sits between your kitchen drains and the sewer. It slows the wastewater down so the grease floats to the top and solids settle to the bottom, and only the cleaner water in the middle moves on to the sewer. You pump out the captured grease on a schedule.

Small kitchens sometimes use an under-sink trap. Larger operations usually need a big in-ground interceptor outside the building. Which one fits your kitchen depends on your flow and your layout, and that's a sizing question, not a guess. I dig into the difference in my post on grease interceptors for restaurants and commercial kitchens if you want to go deeper.

How big does my grease trap need to be?

This is where owners get surprised. The size isn't about the square footage of your dining room. It's driven by your kitchen fixtures, the number and type of sinks, your dishwasher, and how much wastewater you move during a rush.

A barbecue joint, a coffee shop, and a full seafood kitchen on the Fairhope bluff all put out very different grease loads. So the unit that's right for one is the wrong call for the next.

I size these based on your actual fixture schedule and how you run the kitchen, not a one-size number pulled off a shelf. Undersize it and you're pumping constantly and still getting backups. Oversize it and you've spent money and floor space you didn't need to.

Who decides what's required in Fairhope?

The requirements come from your local permitting and utility authorities, and they're specific to your address and your sewer connection. What applies to a build-out on Section Street may not match a site outside the city limits elsewhere in Baldwin County.

I don't want you taking a number off a blog, mine or anyone else's, and building to it. The right move is to confirm the sizing, the required type, and the pump-out and record-keeping rules with the authority that will actually inspect and sign off on your job. They'll tell you exactly what your site needs before you commit.

What I do is handle the plumbing side so it meets what they require the first time. Good commercial kitchen plumbing in Fairhope means the interceptor is placed where it can be serviced, the lines pitch correctly, and the inspector has no reason to fail you.

When should I bring a plumber into the project?

Early. Ideally when you're still looking at floor plans.

The grease interceptor affects where your kitchen drains run, where the unit sits outside, and how your truck access works for pump-outs. If that's an afterthought, you end up cutting slab, moving equipment, or putting the interceptor somewhere a pump truck can't reach it. All of that costs more than planning it right from the start.

On new construction and full build-outs I lay out the whole drain system around the kitchen you're actually building. That's the part of our commercial construction plumbing work that saves owners the most headaches down the road, because the ugly surprises almost always come from drainage and grease, not the pretty fixtures.

What goes wrong when it's done cheap?

The usual failures I get called out for all trace back to shortcuts:

  • An interceptor too small for the kitchen's real load, so it fills and overflows between pump-outs
  • Lines with the wrong slope that let grease pool and harden
  • A unit buried where the pump truck can't get to it
  • Drains tied in wrong so the trap never catches the grease it's supposed to

And Fairhope's climate adds its own wrinkle. Our cold snaps don't last long, but they hit hard enough that exposed and outdoor plumbing needs to be planned for freezing. If you want more on that, I wrote up winter freeze protection for commercial restaurant plumbing specifically for restaurants down here.

Fixing any of this after the fact means opening up work that's already finished. It's always cheaper to do it right while the trenches are still open.

When to Give Me a Call

If you're building, renovating, or taking over a restaurant space anywhere in the Fairhope area, talk to me before you lock in your kitchen layout. I'll look at your fixture schedule, your site, and how you run your kitchen, then build the grease handling and drainage to pass inspection and hold up under a real dinner rush.

Call or text (251) 604-2483 and tell me about your project. I'll give you straight answers on what your build actually needs.

About this article: written for R&D Plumbing Co. LLC with the help of AI. Any facts about R&D Plumbing Co. LLC come from R&D Plumbing Co. LLC's own information.

Got a project? Let's talk.

Commercial-first plumbing across Baldwin County and 60 miles around.